The 10 Scariest Things About Boarding Up A Doorway > 플랫폼 수정 및 개선 진행사항

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Boarding Up a Doorway

Boarding up a doorway keeps hail, snow and rain from further causing damage to the property. It also keeps vandals, squatters and scavengers away.

Doors are more secure than windows, but can still be damaged or kicked. These doors should be set with composite frame that won't warp over time.

Find the Doorway

A doorway is an opening that lets you enter or leave an area, a building, or a passageway. The doorway can also be an entry point that allows access to another location, such as an entirely different room in the same house or different part of the country.

To determine how large the doorway is, it's necessary to measure it. Utilizing a tape measure begin by measuring the length of the frame's inside from one end to the other. Before you take this measurement, it is essential to take out all brickmould and trim pieces. This will allow you to take measurements of the frame, not the actual door or window. Use the largest number of these measurements to determine the width of the doorway.

Make a rough estimate of the opening of the current door if you intend to replace it. You can do this without removing the door by prying the old door away from the jamb using a wide pry tool. This will reveal the rough framing which will be used to hang the new door. The height of the rough opening should be measured three times over and the smallest number will be the height of the new door.

You can also determine the width of your doorway by running a tape measure along the frame at three different locations: center, left and right. Take the measurement with the highest value to determine the width. This is the most effective way to ensure that your plywood will cover the entire area and permit you to put in the door or window you want to replace.

Measure the Frame

24 hour boarding up service up windows, doors, and other openings which let in elements can offer a substantial amount of protection for your home. Begin by carefully examining each window to determine the size and shape. Then, you can measure the width of its frame. Note down each measurement, so that you can accurately cut the plywood boards to be able to fit.

Before you start, wear protective gear to protect yourself from broken glass and other dangers. It is also recommended to work with a partner, as handling large sheets of plywood is easier with an extra set of hands.

Use wide masking to tape the cracks and take off any panes that are not taped. Cover the remaining panes with heavy plastic garbage bags. You can even cover the trash bags inside out to increase their strength.

If the frame is still good it is possible to save time by putting a new stud across the gap that is in the middle of the window. This will give the frame additional strength without requiring the additional effort of taking out and reinstalling the framing.

Acquire a few plywood sheets and tools such as drill, hammer and saw (if cutting is required). Referring to the frame measurements and marking each board with its corresponding window number. Then, using the pilot holes you made earlier, join the plywood to the frame.

Take a look at the Jambs

The jambs are the three pieces of wood that a door is mounted directly. They are vital to keep the door shut properly. They must be secure and even. If the existing jambs aren't, it's time to adjust them.

Begin with the hinge side jambs, with a raised portion towards the center, which is known as a doorstop. The doorstop sits on the slab of the door to keep it from hitting the frame when it closes. Attach a piece of plywood to the bottom of each stud such that it raises the floor inside the opening in about 1/2 inch (photo). This will keep the door from scratching the carpet, tile or throw rug when it is closed and opened.

To get a precise measurement of the hinge's side jamb, you must remove any trim or casing installed around it. This will reveal the opening, which will allow you to accurately measure it.

After you've measured and marking the locations of the hinge holes on both sides of the hinge jamb. Using a combination square, determine the depth of the hinge mortise and adjust the combination square so that it is equal to the mark you made on the jamb of the hinge. This will ensure that the hinge will be centered within the frame and aligned properly with the door. Repeat the process on the jamb side of the door. After you're done, you can employ a nail gun to fix the strike side of the door stop by using 2 1/2-inch nail nails.

Take a look at the Header

A header is a large dimensional lumber board that is attached onto the wall framing. It transfers loads above window and doors openings to the studs below. When properly constructed the King and Jack studs are secured to the opposite side of the header. They also butt up against the header at both ends to create an extremely sturdy column that carries the weight of the opening to the foundation and floor.

In conventionally framed homes you can make use of tables in the code to determine the size of the header to fit a certain span. A typical header is a double 2x12, and the code has tables for three building widths and you can use interpolation to get the next size to determine the correct header size.

There are better options than the standard 2x12 header. They can help save lumber, reduce thermal bridges and allow for more space to be used to create insulation. Mike Guertin examines these options and explains when each is suitable.

He also discusses the rim-board headers that bridge an opening without using the use of a header. This removes an additional step in framing process, and can result in stronger frames. He also talks about box headers which are more difficult to construct, but offer greater spans than single-ply. He also discusses the fastening schedule of these other headers. This requires 8d common nails spaced out every three inches.

Cut the Boards

It is essential to thoroughly prepare the area prior to the process of boarding up the front door. To create enough space to work in and to avoid damage to your possessions, take down all furniture and décor. Take out the doorknobs, locks, and other hardware and put them in a secure place to be used later. To improve adhesion, clean the frame and door and clean all surfaces to get rid of dust and dirt. Sand rough patches if necessary to ensure that the boards are fitted securely and provide adequate protection.

Once the doorway is clear after which it is time to start cutting the plywood boards. A good circular saw will make straight cuts and cut through wood easily and a jigsaw is able to deal with the curved surfaces. Wearing protective gear, such as safety goggles as well as a dust mask is crucial during this step.

After cutting the board to size, it is crucial to check its alignment with the frame and jambs. It is also a good idea to add a few vertical pieces of lumber to the bottom of the board for reinforcement. After the board has been aligned and secured it is now ready to be nailed in place.

A doorway board can safeguard the home or business from being damaged or unauthorized entry in the event of a natural disaster or storm. It can also be used to secure vacant properties or stop burglaries and thefts until the property has been reoccupied. A thorough assessment of the situation and the purpose of the boarding up commercial property will aid in determining the best selection of the material and method of installation to achieve the most effective results.

Install the Boards

Instead of nailing the boards instead, use screws that are strong enough to fix the boards. These fasteners are durable and will resist prying. This will increase the effectiveness of your board. Sealing the edges with caulk or weatherstripping can stop water and wind from leaking through gaps. It's also an excellent idea to leave a gap for ventilation to avoid stuffy air and the accumulation of moisture.

Wearing gloves and goggles is essential when working with a power tool. It is also recommended to use a straightedge and pencil to mark your cuts because mistakes are more difficult to fix once you've completed cutting. You'll want to make your cut as precise as you can so that the boards fit perfectly against the door casing and frame. The jambs and head must be cut so that they are level with the wall.

It is recommended to do this prior to an event to allow time to secure any other areas that are at risk. A little planning will save you a lot of work and will help you prepare your business or home for an impending catastrophe. Your property can be protected from wind, criminal activity and flying debris with the right preparation. It will also give you peace of mind knowing your property is protected from damage.